2022 Manitoba Workplace Safety and Health Act and Regulation
Yüklə 1,63 Mb. Pdf görüntüsü
|
- Bu səhifədəki naviqasiya:
- UPRIGHTS (Vertical) STRINGERS / WALES (Horizontal) CROSS-BRACES, STRUTS (Horizontal)
- Schedule — Minimum shoring requirements subsection 26.15(2), 26.16(4) and 26.24(1)
- UPRIGHTS (Vertical) STRINGERS / WALES (Horizontal) CROSS-BRACES, STRUTS (Horizontal)
- “strut”
- PART 27 WORK IN A COMPRESSED AIR ENVIRONMENT Application 27.1
- Safe work procedures 27.2
- General requirements 27.3(1)
- PART 28 SCAFFOLDS AND OTHER ELEVATED WORK PLATFORMS GENERAL REQUIREMENTS Application 28.1(1)
- Safe work procedures 28.2(1)
|
UPRIGHTS (Vertical)
STRINGERS / WALES (Horizontal) CROSS-BRACES, STRUTS (Horizontal) Category 1b Stiff fissured soils, and stiff clay fills Depth Member minimum dimensions Maximum spacing horizontally Member minimum dimensions Maximum spacing horizontally Member minimum dimensions (mm) Maximum spacing vertically (to match Stringers / Wales) Maximum spacing horizontally along Stringers / Wales Width of Trench (m) (m) (mm) (mm) (mm) (mm) less than 1.8 m. 1.8 m. to 3.7 m. (mm) (mm) 1.5 - 3.0 m 89 x 140 686 89 x 140 1200 89 x 89 140 x 140 1200 796 3.0 - 4.5 m 89 x 140 564 191 x 191 915 89 x 89 140 x 140 915 939 UPRIGHTS (Vertical) STRINGERS / WALES (Horizontal) CROSS-BRACES, STRUTS (Horizontal) Category 2 Soft cohesive soils, and stiff to wet/loose silt soils Depth Member minimum dimensions Maximum spacing horizontally Member minimum dimensions Maximum spacing horizontally Member minimum dimensions (mm) Maximum spacing vertically (to match Stringers / Wales) Maximum spacing horizontally along Stringers / Wales Width of Trench (m) (m) (mm) (mm) (mm) (mm) less than 1.8 m. 1.8 m. to 3.7 m. (mm) (mm) 1.5 - 3.0 m 38 x 235 229 89 x 140 1200 89 x 89 140 x 140 1200 918 3.0 - 4.5 m 89 x 140 457 191 x 191 915 89 x 89 140 x 140 915 887 Schedule — Minimum shoring requirements subsection 26.15(2), 26.16(4) and 26.24(1) Workplace Safety And Health Regulation 247 UPRIGHTS (Vertical Members) STRINGERS / WALES (Horizontal Members)* CROSS-BRACES, STRUTS (Horizontal)* Category 1a Stiff clays and stiff to hard clay tills, and stiff fissured clays Depth Member minimum dimensions Maximum spacing horizontally Member minimum dimensions Maximum spacing horizontally Member minimum dimensions (mm) Maximum spacing vertically (to match Stringers / Wales) Maximum spacing horizontally along Stringers / Wales Width of Trench (m) (m) (mm) (mm) (mm) (mm) less than 1.8 m. 1.8 m. to 3.7 m. (mm) (mm) 1.5 - 3.0 m 38 x 235 384 89 x 140 1200 89 x 89 140 x 140 1200 1291 3.0 - 4.5 m 38 x 235 344 191 x 191 915 89 x 89 140 x 140 915 1475 UPRIGHTS (Vertical) STRINGERS / WALES (Horizontal) CROSS-BRACES, STRUTS (Horizontal) Category 1b Stiff fissured soils, and stiff clay fills Depth Member minimum dimensions Maximum spacing horizontally Member minimum dimensions Maximum spacing horizontally Member minimum dimensions (mm) Maximum spacing vertically (to match Stringers / Wales) Maximum spacing horizontally along Stringers / Wales Width of Trench (m) (m) (mm) (mm) (mm) (mm) less than 1.8 m. 1.8 m. to 3.7 m. (mm) (mm) 1.5 - 3.0 m 89 x 140 686 89 x 140 1200 89 x 89 140 x 140 1200 796 3.0 - 4.5 m 89 x 140 564 191 x 191 915 89 x 89 140 x 140 915 939 UPRIGHTS (Vertical) STRINGERS / WALES (Horizontal) CROSS-BRACES, STRUTS (Horizontal) Category 2 Soft cohesive soils, and stiff to wet/loose silt soils Depth Member minimum dimensions Maximum spacing horizontally Member minimum dimensions Maximum spacing horizontally Member minimum dimensions (mm) Maximum spacing vertically (to match Stringers / Wales) Maximum spacing horizontally along Stringers / Wales Width of Trench (m) (m) (mm) (mm) (mm) (mm) less than 1.8 m. 1.8 m. to 3.7 m. (mm) (mm) 1.5 - 3.0 m 38 x 235 229 89 x 140 1200 89 x 89 140 x 140 1200 918 3.0 - 4.5 m 89 x 140 457 191 x 191 915 89 x 89 140 x 140 915 887 Workplace Safety And Health Regulation 248 UPRIGHTS (Vertical) STRINGERS / WALES (Horizontal) CROSS-BRACES, STRUTS (Horizontal) Category 3a Cohesionless: loose to me- dium dense soils Depth Member minimum dimensions Maximum spacing horizontally Member minimum dimensions Maximum spacing horizontally Member minimum dimensions (mm) Maximum spacing vertically (to match Stringers / Wales) Maximum spacing horizontally along Stringers / Wales Width of Trench (m) (m) (mm) (mm) (mm) (mm) less than 1.8 m. 1.8 m. to 3.7 m. (mm) (mm) 1.5 - 3.0 m 38 x 235 326 89 x 140 1200 89 x 89 140 x 140 1200 1193 3.0 - 4.5 m 38 x 235 293 191 x 191 915 89 x 89 140 x 140 915 1359 UPRIGHTS (Vertical) STRINGERS / WALES (Horizontal) CROSS-BRACES, STRUTS (Horizontal) Category 3b Cohesionless: dense to very dense soils Depth Member minimum dimensions Maximum spacing horizontally Member minimum dimensions Maximum spacing horizontally Member minimum dimensions (mm) Maximum spacing vertically (to match Stringers / Wales) Maximum spacing horizontally along Stringers / Wales Width of Trench (m) (m) (mm) (mm) (mm) (mm) less than 1.8 m. 1.8 m. to 3.7 m. (mm) (mm) 1.5 - 3.0 m 38 x 235 460 89 x 140 1200 89 x 89 140 x 140 1200 1414 3.0 - 4.5 m 38 x 235 415 191 x 191 915 89 x 89 140 x 140 915 1616 * Notes for Table: 1. All spacings shown are centre-to-centre of members. 2. Design based on 086.1-2001 Wood Design Manual; all “uprights” (vertical shoring) to be minimum 2-span continuous (cantilevers not to be included as “spans”). All shoring assumed to have members orientated for weak-axis bending. 3. All members to be graded lumber meeting S.P.F. No. 2 or better. 4. In this Schedule: “strut” means a horizontal cross-member of shoring that directly resists pressure; (« étrésillon ») “upright” means a vertical shoring member that is placed against and directly resists pressure from a wall of an excavation; (« montant ») “wale” means a horizontal shoring member that is placed parallel to the excavation face and whose sides bear against the vertical shoring member or the earth. M.R. 128/2019 Workplace Safety And Health Regulation 249 UPRIGHTS (Vertical) STRINGERS / WALES (Horizontal) CROSS-BRACES, STRUTS (Horizontal) Category 3a Cohesionless: loose to me- dium dense soils Depth Member minimum dimensions Maximum spacing horizontally Member minimum dimensions Maximum spacing horizontally Member minimum dimensions (mm) Maximum spacing vertically (to match Stringers / Wales) Maximum spacing horizontally along Stringers / Wales Width of Trench (m) (m) (mm) (mm) (mm) (mm) less than 1.8 m. 1.8 m. to 3.7 m. (mm) (mm) 1.5 - 3.0 m 38 x 235 326 89 x 140 1200 89 x 89 140 x 140 1200 1193 3.0 - 4.5 m 38 x 235 293 191 x 191 915 89 x 89 140 x 140 915 1359 UPRIGHTS (Vertical) STRINGERS / WALES (Horizontal) CROSS-BRACES, STRUTS (Horizontal) Category 3b Cohesionless: dense to very dense soils Depth Member minimum dimensions Maximum spacing horizontally Member minimum dimensions Maximum spacing horizontally Member minimum dimensions (mm) Maximum spacing vertically (to match Stringers / Wales) Maximum spacing horizontally along Stringers / Wales Width of Trench (m) (m) (mm) (mm) (mm) (mm) less than 1.8 m. 1.8 m. to 3.7 m. (mm) (mm) 1.5 - 3.0 m 38 x 235 460 89 x 140 1200 89 x 89 140 x 140 1200 1414 3.0 - 4.5 m 38 x 235 415 191 x 191 915 89 x 89 140 x 140 915 1616 Workplace Safety And Health Regulation 250 PART 27 WORK IN A COMPRESSED AIR ENVIRONMENT Application 27.1 This Part applies to every workplace where work is done in a compressed air environment, but does not apply to divers or to persons working in diving bells. Safe work procedures 27.2 An employer must (a) develop and implement safe work procedures for working in a compressed air environment; (b) train workers who may perform work in a compressed air environment in those safe work procedures; and (c) ensure that workers comply with those safe work procedures. General requirements 27.3(1) An employer must, before allowing or permitting a worker to enter a compressed air environment, (a) ensure that the branch is notified of the nature and location of the work in writing, at least 30 days in advance of the work beginning; and (b) establish a comprehensive work plan for work in compressed air that (i) has been developed and approved by a professional engineer, and (ii) meet the requirements of CSA Z275.3-09 (R2014), Occupational safety code for work in compressed air environments. 27.3(2) An employer must ensure that work done in a compressed air environment is done in accordance with the work plan established under clause (1)(b). M.R. 90/2014; 128/2019 Workplace Safety And Health Regulation 251 PART 28 SCAFFOLDS AND OTHER ELEVATED WORK PLATFORMS GENERAL REQUIREMENTS Application 28.1(1) This Part applies to every workplace where work takes place using a scaffold or elevated work platform. 28.1(2) Except for work of short duration that can be done safely from a ladder, an employer must ensure that a worker engaged in work that cannot be done from the ground or other safe elevation is provided with a scaffold or an elevated work platform. Safe work procedures 28.2(1) When a scaffold or an elevated work platform is required to be provided at a workplace, the employer must (a) develop and implement safe work procedures for using the scaffold or elevated work platform provided; (b) train workers who work on scaffolds and elevated platforms in those safe work procedures; and (c) ensure that the workers comply with those safe work procedures. 28.2(2) An employer must ensure that the safe work procedures developed in subsection (1) include emergency response and rescue procedures appropriate to the risks associated with the failure of a scaffold or other elevated work platform. Yüklə 1,63 Mb. Dostları ilə paylaş:
|